pdns-recursor versions 3.1.7.2 and 3.2 use the function “swapcontext” which is not supported by glibc (version 2.11.2-r3 and most likely not any other version either) on arm. If, for some reason, you want recursive DNS use unbound (version 1.4.3 worked for me). If you want PHP, go with 5.3.3 or greater otherwise you may get Segmentation Faults. 5020 FreeAgent GoFlex 5021 FreeAgent GoFlex USB 2.0 5030 FreeAgent GoFlex. Kernel Modules):Īnd followed the rest of the handbook until the end.įail2Ban-0.8.4-r2, Shorewall-Perl-4.2.11.1 and Nut-2.4.3-r2 all installed and ran just fine even though they were masked by “missing keyword” 0a6b Green House Co., Ltd 0001 Compact Flash R/W with. If you have any kernel modules I recommend you “make modules”. Note: I didn’t use vanilla-sources, I used gentoo-sources Raid Network Attached Storage (NAS) Data Recovery - USB Flash Drive Data Recovery. I followed just the instructions for “ 5. We also provide worldwide SATA SAS Raid Seagate FreeAgent NAS Data. Make sure you add the swap file to fstab so that it gets used otherwise you will get compile failures when the dockstar runs out of memory. Instead of a swap partition, I made a 1GB swap file like this:ĭd if=/dev/zero of=/mnt/gentoo/.swapfile count=2M I made the whole drive one big ext3 partition because I suspected that the uBoot bootloader that I used wouldn’t accept more then one partition. FreeAgent GoFlex Net Media Sharing Device, FreeAgent DockStar, Seagate. Make sure you run the command to tell it you want to use ext3 for you boot partition. JWM4 We provide USB Flash Data Recovery, NAND chip data recovery, SSD Data. provides Biloxi Seagate Business Storage NAS raid server data recovery to Corporate, Business and. The hardware I used was a Seagate Dockstar model# STDSA10G-RK with an external FreeAgent Go hard disk model# ST903203FGA2E1-RKĪnd followed everything up to “ Things To Do After First Boot“. SEAGATE FREEAGENT DOCKSTAR BLINKING GREEN FOREVER FULL VERSIONIf I have time at some point I intend on posting a more full version so this “guide” does not have to rely on someone else’s “guide” that may not be there later.ĭISCLAIMER: This site and any of it’s admins/moderators/staff and myself cannot be held responsible if anyone follows this “guide” and damages or “ bricks” their dockstar (or damages anything else) while using, in full or in part, the information presented here. SEAGATE FREEAGENT DOCKSTAR BLINKING GREEN FOREVER FREESeagate Free Agent External Hard Drives, Seagate GoFlex External Hard. What does “short version” mean? It means that it just points to the relevant bits of the relevant guides that I followed to make it work. provides Waldorf flash data recovery and USB Flash. Nope, according to the Seagate sites, a flashing/blinking orange light indicates a boot error: 'The Seagate FreeAgent Dockstar failed to boot up normally.'. Each time you connect the drive you may have to do this. You can set one manually or leave it for about 25 minutes for one to be allocated auto. This is just the short version of what I did to put gentoo on a Seagate Dockstar. We provide Idaho Bright Drive Astella Server raid server data recovery for SATA hard drives, usb flash drives, SAS raid hard drives, macintosh drives and. Re: New Dockstar: Orange/Amber light flickers, no sign of the device in the network. Connect the drive but do not Format the drive, right click 'my computer' then 'manage' go to 'storage/disk management' view the drives your usb drive will not be allocated a drive letter.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |